Search found 180 matches

by hotpaw2
Mon Aug 24, 2020 3:01 pm
Forum: RTL-SDR Discussion
Topic: Can any RF chip be modded to turn into an sdr or only R820T?
Replies: 6
Views: 2050

Re: Can any RF chip be modded to turn into an sdr or only R820T?

Depends on what you mean by an SDR. Most WiFi, cellular, and mobile phone radios are SDRs internally. So you don't need to turn them into an SDR, as they already are SDRs. However the RF frequencies and modulations these SDR chips are capable of are often fixed to specifics bands and modes, and the ...
by hotpaw2
Tue Aug 18, 2020 2:39 pm
Forum: Troubleshooting Help
Topic: want to broadcast radio [!help]
Replies: 4
Views: 1712

Re: want to broadcast radio [!help]

Some countries allow license-free broadcasting within a limited range of frequencies if one stays below mandated power levels and transmits with a given spectral purity. An amateur radio license will allow one to use even more frequency bands at much higher power levels. Check the requirements for y...
by hotpaw2
Mon Aug 17, 2020 8:43 pm
Forum: Troubleshooting Help
Topic: Librtlsdr vs SDR# sensitivity
Replies: 1
Views: 927

Re: Librtlsdr vs SDR# sensitivity

Check your rtlsdr_set_tuner_gain, rtlsdr_set_tuner_gain_mode, and rtlsdr_set_agc_mode settings.
If the AGC is off and your RF gain is way down, the RTL-SDR sensitivity will be low.
by hotpaw2
Mon Aug 03, 2020 3:44 pm
Forum: RTL-SDR Discussion
Topic: Direct sampling to bandwidth output, how done?
Replies: 10
Views: 4090

Re: Direct sampling to bandwidth output, how done?

The mathematically correct solution is to use a perfect band-limiting anti-aliasing or low-pass filter before decimation or interpolation. In reality, no filter is perfect. So an anti-aliasing filter should have a stop band attenuation below the radio's desired noise floor at and above the new downs...
by hotpaw2
Wed Jun 17, 2020 2:56 pm
Forum: Signal Identification Help
Topic: Is this interference i see at 137MHz?
Replies: 23
Views: 10052

Re: Is this interference i see at 137MHz?

One additional trick that can help is to use ferrite beads or toroids. I prefer toroids, as multiple turns through the donut seem to work better than a string of multiple cores/beads on the cables. Try 1 or 2 meter passive USB cable, but loop several turns of the cable through a ferrite toroid, mayb...
by hotpaw2
Thu May 28, 2020 8:55 pm
Forum: Antennas
Topic: Airspy YouLoop
Replies: 17
Views: 8451

Re: Airspy YouLoop

A YouLoop type antenna requires a receiver with a high-gain low-noise RF front end, such as an AirSpy HF+ Discovery. IIRC, an ordinary RTL-SDR in direct sampling mode doesn't have that much RF gain, and its 8-bit sampling creates a relatively high noise floor, so you might want to try using an LNA b...
by hotpaw2
Thu May 14, 2020 2:43 pm
Forum: RTL-SDR Discussion
Topic: GQRX - unexpected plot when changing frequency range
Replies: 14
Views: 8328

Re: GQRX - unexpected plot when changing frequency range

The bigger the input signal, the more likely the spectrum is to show spurious signals (intermodulation products, etc.). That's because semiconductor devices are non-linear components. They are only approximately linear enough for a range right above the smallest signals detectable. Near the maximum ...
by hotpaw2
Sun May 10, 2020 7:44 pm
Forum: Troubleshooting Help
Topic: Installing RTL-SDR: Cmake error - LibUSB 1.0 required to compile rtl-sdr
Replies: 11
Views: 7841

Re: Installing RTL-SDR: Cmake error - LibUSB 1.0 required to compile rtl-sdr

Make sure you installed libusb itself, and not just the libusb build essentials developer tools.

or download libusb from GitHub and build, and then make install it.

https://github.com/libusb/libusb
by hotpaw2
Wed May 06, 2020 5:56 pm
Forum: RTL-SDR Discussion
Topic: GQRX - unexpected plot when changing frequency range
Replies: 14
Views: 8328

Re: GQRX - unexpected plot when changing frequency range

The first step is being able to detect real signals is to test against real signals and their absence and make sure your equipment is calibrated to tell the difference. You might even need some sort of signal generator and some attenuators, etc. to do this.
by hotpaw2
Tue May 05, 2020 10:31 pm
Forum: RTL-SDR Discussion
Topic: GQRX - unexpected plot when changing frequency range
Replies: 14
Views: 8328

Re: GQRX - unexpected plot when changing frequency range

The signals in your waterfall screenshots look more like spurious intermodulation products or oscillator birdies than real RF signals. Try again after you find a "real" signal, e.g. one you can listen to or decode. Shift up or down a quarter of a frame after you find a signal with a station ID or so...