New Version R1700 SpyServer from Airspy

Need help installing or figuring out something about your SDR? Ask here.
Post Reply
creinemann
Posts: 1
Joined: Sun Aug 26, 2018 9:38 pm

New Version R1700 SpyServer from Airspy

Post by creinemann » Mon Nov 26, 2018 10:22 pm

I have been having some setup issues with the new Version of Spyserver version R1700 from Airspy (SDR# folks). I have the server set up and running so I can access the V3 Dongle remotely just fine. But there are settings in the spyserver.config file that allow the server to be listed on https://airspy.com/directory/ for others to log into. I cannot seem to get mine to show up on the page. I had it there for a few minutes, then it disappeared., I have my config file below. I have my ports forwarded (TCP/UDP) from 5555-6666. What am I missing?

# SPY Server Configuration File

# TCP Listener
#
bind_host = 0.0.0.0
bind_port = 5555-6666

# List Server in Airspy Directory
#
list_in_directory = 1

# Owner Name
# For example: RTL-SDR User
owner_name =HammerOne

# Owner email
# For example: [email protected]
owner_email =cr*^%$8&@gmail.com

# Antenna
# For example: Random Wire/Magnetic Loop/Mini-Whip/Inverted V/etc.
antenna_type =Long Wire 65'

# Antenna Location
# For example: 48.858332, 2.294560
antenna_location =43.007054,-88.800268

# General Description
#
general_description = Wisconsin, USA

# User sessions
#
maximum_clients = 5

# Maximum session duration
# In minutes. 0 for no limit
#
maximum_session_duration = 0

# Allow clients to retune and change of gain of the device
#
allow_control = 1

# Device Type
# Possible Values:
# AirspyOne (R0, R2, Mini)
# AirspyHF+
# RTL-SDR
# Auto (Scans for the first available device)
#
device_type = RTL-SDR

# Device Serial Number as 64bit Hex
# For example: 0xDD52D95C904534AD
# A value of 0 will acquire the first available device.
#
device_serial = 3

# Device Sample Rate
# Possible Values:
# Airspy R0, R2 : 10000000 or 2500000
# Airspy Mini : 6000000 or 3000000
# Airspy HF+ : 768000
# RTL-SDR : 500000 to 3200000
# Comment to use the device's default
#
#device_sample_rate = 2500000

# Force 8bit Compression Mode
# The 8bit Compression mode has proven sufficiently good for most streaming use cases.
# Use it to same some internet bandwidth.
#
#force_8bit = 1

# Maximum Bandwidth
# Limits the maximum IQ bandwidth the clients can set
# Recommended value for WFM is 200000
# Recommended value for narrow band modes is 15000
#
#maximum_bandwidth = 15000

# FFT Frames Per Second
#
fft_fps = 15

# FFT Bins
# Bins = 2^fft_bin_bits
#
fft_bin_bits = 16

# Initial Center Frequency
#
#initial_frequency = 7100000

# Minimum Tunable Frequency
# Comment if using the device default
#
minimum_frequency = 0

# Maximum Tunable Frequency
# Comment if using the device default
#
maximum_frequency = 54000000

# Frequency Correction in PPB
#
frequency_correction_ppb = -1000

# Initial Gain
#
#initial_gain = 10

# RTL-SDR Sampling mode
# Quadrature = 0,
# Direct Sampling I Branch = 1
# Direct Sampling Q Branch = 2
rtl_sampling_mode = 2

# Converter Offset
# Set to -120000000 to enable the SpyVerter offset
#converter_offset = -120000000

# Bias-Tee
# For AirspyOne only - Useful for LNA's and SpyVerter
#enable_bias_tee = 0

# Buffer Size (in milliseconds)
#
buffer_size_ms = 50

# Buffer Count
#
buffer_count = 10

Post Reply