cd pkg-rtl-sdr
rm build -r
mkdir build
cd build
cmake ../ -DINSTALL_UDEV_RULES=ON
make
sudo make install
sudo cp ../rtl-sdr.rules /etc/udev/rules.d/
sudo ldconfig
echo ‘blacklist dvb_usb_rtl28xxu’ | sudo tee –append /etc/modprobe.d/blacklist-dvb_usb_rtl28xxu.conf
====================
Startup from the command prompt
====================
replace 192.168.1.119 with the IP Address of your RPi
rtl_tcp -a 192.168.1.119 -p 1234 -D 2
====================
to connect from a Windows PC
====================
SDR Radio Console and SDRSharp tested and work fine.
Use the regular TCP setup.
Chris
4 years ago
#136562
What is here happend? Where have to be the File right now?
CMake Error: The current CMakeCache.txt directory /home/geeko/rtl-sdr/pkg-rtl-sdr/CMakeCache.txt is different than the directory /home/geeko/pkg-rtl-sdr where CMakeCache.txt was created. This may result in binaries being created in the wrong place.
KevinP
5 years ago
#125897
if you havent gotten an answer yet. Here’s what worked for me.
do the following one line at a time……
cd pkg-rtl-sdr
cmake -G “Unix Makefiles”
make
make install
Steve Sykes
5 years ago
#119135
How is this driver installed on a raspberry pi? The normal cmake doesn’t seem to work.
Regards
Steve KD2OM
this worked for me
to install rtl_tcp to run on RPi
11/25/2019
====================
download files
====================
from Raspberry Pi..
open in browser:
https://www.rtl-sdr.com/rtl-sdr-blog-v-3-dongles-user-guide/rtl-sdr-driver-patched-by-pietertjerk/comment-page-1/
click the link:
rtl-sdr-driver-patched-by-PieterTjerk
zip file will open in Archiver
click icon upper right to extract files to /home/pi
====================
Installation (Linux):
====================
open a Terminal window and run the following commands
sudo apt update
sudo apt install libusb-1.0-0-dev git cmake
cd pkg-rtl-sdr
rm build -r
mkdir build
cd build
cmake ../ -DINSTALL_UDEV_RULES=ON
make
sudo make install
sudo cp ../rtl-sdr.rules /etc/udev/rules.d/
sudo ldconfig
echo ‘blacklist dvb_usb_rtl28xxu’ | sudo tee –append /etc/modprobe.d/blacklist-dvb_usb_rtl28xxu.conf
====================
Startup from the command prompt
====================
replace 192.168.1.119 with the IP Address of your RPi
rtl_tcp -a 192.168.1.119 -p 1234 -D 2
====================
to connect from a Windows PC
====================
SDR Radio Console and SDRSharp tested and work fine.
Use the regular TCP setup.
What is here happend? Where have to be the File right now?
CMake Error: The current CMakeCache.txt directory /home/geeko/rtl-sdr/pkg-rtl-sdr/CMakeCache.txt is different than the directory /home/geeko/pkg-rtl-sdr where CMakeCache.txt was created. This may result in binaries being created in the wrong place.
if you havent gotten an answer yet. Here’s what worked for me.
do the following one line at a time……
cd pkg-rtl-sdr
cmake -G “Unix Makefiles”
make
make install
How is this driver installed on a raspberry pi? The normal cmake doesn’t seem to work.
Regards
Steve KD2OM
you ever figure out to make it work on a Pi?