Tagged: AMSAT

Amateur Radio on the Es’hail-2 Satellite Explained on YouTube

Over on YouTube Tech Minds has posted a video explaining what Es'hail-2 satellite is and why it is interesting for hams and SDR users. Briefly Es'hail-2 is a recently launched geostationary TV satellite that covers Africa, Europe, the Middle East, India, eastern Brazil and the west half of Russia/Asia.

What's special about it is that apart from the TV transmitters, it also contains the worlds first amateur radio transponder in geostationary orbit. So amateur radio users within the region covered by the satellite can simply point their antennas to a fixed position in the sky to transmit to the satellite, and the signal will be rebroadcast over the entire covered area. With a simple LNB, satellite dish and SDR the signals can be received.

After explaining Es'hail-2 Tech Minds also shows a demo of Es'hail-2 radio traffic using a public WebSDR.

The Worlds First Geostationary Satellite For Ham Radio - Es'Hail 2 - Qatar OSCAR-100

Es’hail-2 Amateur Transponder Now Active

Es'Hail 2 Coverage
Es'Hail 2 Coverage from Amsat-UK

Es'hail 2 was launched last November and it is the first geostationary satellite to contain an amateur radio transponder. The satellite is positioned at 25.5°E which is over Africa. It's reception footprint covers Africa, Europe, the Middle East, India, eastern Brazil and the west half of Russia/Asia. There are two amateur transponders on the satellite. One is a narrow band linear transponder which uplinks from  2400.050 - 2400.300 MHz and downlinks from 10489.550 - 10489.800 MHz. Another is a wide band digital transponder for amateur digital TV which uplinks from 2401.500 - 2409.500 MHz and downlinks from 10491.000 - 10499.000 MHz.

Although it launched last year it takes several months for the engineers to test and qualify the transponder for use. Over the last few weeks the transponder was intermittently active during the testing, but now since Feb 13 2019 the amateur transponder has finally been fully activated for amateur radio use.

To receive it with an RTL-SDR or most other SDRs an LNB is required to receive the 10 GHz signal and downconvert it into a frequency range that most SDRs support. Typically an Octagon LNB is used, and these are easy to find and cheap as they are often used for satellite TV.

From various reports seen on Twitter, it seems that the signal is strong enough that a satellite dish is not required for receiving - simply pointing the LNB directly at the satellite is enough.

If you can't set up a receiver, there is an OpenWebRX livestream of the Es'hail 2 narrowband channel that has been set up by Zoltan/RFSparkling which is available at sniffing.ddns.net:8073 (note the server can only handle 8 users at a time, so try again later if it's busy). Also as pointed out by KD9IXX on Twitter, there are also several websdr.org servers receiving and streaming Es'hail2 including an Airspy based one run officially by AMSAT-DL.

Es’hail-2 Transponder Tests + Narrow Band Web Stream

Es'hail 2 was launched last November and it is the first geostationary satellite to contain an amateur radio transponder. The satellite is positioned at 25.5°E which is over Africa. It's reception footprint covers Africa, Europe, the Middle East, India, eastern Brazil and the west half of Russia/Asia.

Although the satellite was launched last year, turning on the amateur transponders has been slow because the commercial systems of the satellite have higher priority for testing and commissioning. However, within the last day the Es'hail 2 team have now begin testing the amateur transponder, and the test signal has been successfully received by several enthusiasts (just check out the Twitter feed). There also appears to have already been a suspected pirate CW signal broadcasting "WELCOME DE ES2HAIL". Actual uplink use of the satellite is not currently wanted, and from the Amsat forums one of the engineers writes:

Before the IOT starts there will be a TRR (test readyness review) in front of the customer. All the testplans and test-specifications will be reviewed. When the test is done there will be a TRB (test readyness board). In the TRB they have to show/present all the measurement results (e.g. inband performance like Gainflatness, Groupdelay... aso.) and compare these results with the specification in the contract. Each unwanted signal makes the measurement difficult and needs to be explained or leads to a so named NCR (non conformance report).

The IOT will be done in shifts/nightshifts and with unwanted signals (if not explain able) some measurements needs to start again and again and leads in addition to a delay for the handover and operation of the satellite.

Maybe that helps to understand why it is really important to have only the IOT uplink signal.

To measure the pattern of each antenna the satellite will be moved east/west by the propulsion system of the DS2000 Bus and the signal level is measured by the IOT station on ground (some cuts) .

The commercial beacon can maybe be switched from LEOP Omni antenna to on station antenna when the satellite is placed in the final slot. This should be the reason for the change of the commercial Ku Band beacon signal level the last days.

If you are interested in receiving Es'hail 2, but live outside the footprint, or don't have a receiver then you can use Zoltan's OpenwebRX live stream of the narrow band portion of the Es'hail 2 downlink. At the moment the beacon doesn't appear to be transmitting, but we expect it to be on and off during the next few days. In his set up he uses an RTL-SDR V3, Inverto LNB, 90cm dish, a DIY bias tee and a Raspberry Pi 3.

He also took a recording of the pirates CW transmission shown in the video below.

Es'hail-2 live, CW signal 2019.01.17.

Es-hail 2 test transmission
Es-hail 2 test transmission

Building a Carbon Fibre Dual Band Yagi Antenna for Amateur Radio Satellites with 3D Printed Parts for 20€

Back in early 2017 we posted about Manuel's (aka DO5TY / Tysonpower) design for a single band 140 MHz 3D printed carbon fibre Yagi antenna. Today he's submitted a new video about creating a dual band 3D printed carbon fibre cross Yagi antenna for only 20€. Note that the video is narrated in German, but there are English subtitles. He's also uploaded an English text tutorial to his blog, which includes links to the 3D printer STL files.

The antenna is designed to be a low cost replacement for the commonly used Arrow dual band 2m/70cm antenna which is designed for receiving and transmitting to amateur radio satellites. Many amateur radio satellites have an uplink frequency set at around 145 MHz, and a downlink frequency around 435 MHz (and some satellites have the frequencies reversed). So a dual band Yagi is ideal for these satellites. Manuel writes that with his 5W Baofeng handheld he's already made several successful contacts with his new antenna.

Manuel's antenna consists of several 3D printed joints, with a carbon fibre rod used as the main boom. Aluminum rods make up the receiving and transmitting elements. The video also discusses impedance matching and how he uses a diplexor so that there is only one connection required to the radio. The advantage of his antenna over the Arrow is that it is significantly cheaper, and also much lighter in weight.

[EN subs]Carbon Arrow Yagi Antenne - leichte Dual Band Yagi für 20€ bauen

Es’hail-2: First Geostationary Satellite with Amateur Radio Transponders Successfully Deployed

Today SpaceX have successfully launched and deployed the Es'hail-2 satellite which is now in geostationary orbit. This launch is special for amateur radio enthusiasts because it is the first geostationary satellite that contains an amateur radio transponder on it. The satellite is positioned at 25.5°E which is over Africa. It will cover Africa, Europe, the Middle East, India, eastern Brazil and the west half of Russia/Asia. Unfortunately, North America, Japan, most of South America, Australia and NZ miss out.

Coverage of Es'hail 2
Coverage of Es'hail 2

The satellite has a two bandwidth segments, a 250 kHz narrow band for modes like SSB, FreeDV, CW, RTTY etc, and a 8 MHz wide band for digital amateur TV (DATV) modes like DVB-S and DVB-T.

The downlink frequencies are at 10 GHz so a low cost TV LNB could be used as the antenna. For receiving the narrowband modes, an RTL-SDR or similar SDR could be used, and for the 8 MHz DATV modes a standard DVB-S2 set top box can be used to receive and decode the video. For uplink, the transmission frequency is at 2.4 GHz.

According to the commissioning order of the satellite, it is expected that the AMSAT transponders will be activated only after all tests have been passed, and after other higher priority commercial telecommunications systems have been activated. This is expected to take about 1-2 months.

2018: Es'hail-2 and its amateur radio payload - Graham Shirville (G3VZV) & Dave Crump (G8GKQ)