Tagged: gain

Windows Version of the Fully Exposed RTL-SDR Driver now Available

Last week we posted about Milen Rangelov’s (gat3way) new RTL-SDR driver which has exposed filter and gain settings for the R820T/2 chip. This should let you tweak for optimal reception much better. Previously the driver was only available for Linux, however, now over on SourceForge user randaller has ported this driver to Windows.

To use the driver in SDR# simply unzip all the files into the SDR# folder, then while using the dongle in SDR# open the librtlsdr_wincontrol.exe file to open the control interface. The interface also has the ability to directly write values to a register, which together with the newly released register datasheet, can be useful for experimenting with the R820T2 chip.

The description reads:

Unpack all files to SDRSharp folder, start SDR# playback, then run controller exe file.
Do not forget to allow software to use UDP/32323 port in your firewall.

You may use this rtlsdr.dll with osmocom or other software, of course.
It is fully compatible to original one.

There are UDP server on 32323 port inside of rtlsdr.dll. It accepts and answers \n-terminated strings and accept two easy commands: get and set register. Examples:
g 5\n – will return value of R5
s 7 10 15\n – will set four lowest bits (mask 0x0f) of R7 with value 10
s 12 174 255\n – will write complete byte to R12
All values should be decimal.
You may use this feature to develop own gui controller with beauty knobs.

 

The driver GUI.
The driver GUI.

New Linux RTL-SDR Driver with Fully Exposed Controls

A new Linux based driver for the RTL-SDR has been released by Milen Rangelov (aka gat3way) which exposes all the adjustable settings on the R820T/2 tuner chips. This exposes adjustable sliders for settings like preselection, IF and notch filters and the multiple gain stages on the R820T/2. In the standard drivers the filters and gain settings are mostly set automatically, but manually adjusting them could yield better results. The filters are not very strong, but they could be used to help block out an interfering signal, increasing the dynamic range of the RTL-SDR.

Over on his post at r/rtlsdr Milen wrote the following about his driver:

The idea in brief is to modify the librtlsdr code so that an unix domain socket server receives i2c register set/get commands and executes them. It only works for r820t tuners. This modified rtlsdr library is then dynamically preloaded by means of LD_PRELOAD and used by the SDR software. This is actually what happens when you call r820tweak <program>. This way, no modifications to both gr-osmosdr source and the SDR program are required, instead of waiting for them to implement those controls, we kind of have a separate program that tweaks them.

The GUI program is a simple wxpython client, it currently exposes the following settings:

LNA, Mixer, VGA gain stages – the 3 variable gain stages

LPF/HPF filter cutoff – these control the “width” of the r820t2 lowpass/highpass filters, those filters are relatively sharp and this in turn is very useful to increase the dynamic range by fitlering out strong signals “close” to the weak signal you are hunting. Those are among the nicest features to play with, together with the gain stages.

LPNF cutoff – apparently there is also a low pass notch filter, however this doesn’t work as I expected. Anyway, still useful as a kind of variable attenuator.

Filter bandwidth – there is a bandpass filter which isn’t quite “sharp” at all, centered at the center frequency. Kind of additional filter, easier to manipulate than the rest of them, but not that powerful. May provide some extra dynamic range. Behaves kind of weird when gqrx decimation is used.

As far as the gain stages are concerned – the LNA gain is the first stage and thus the most important – it determines the SNR. Mixer gain is less important (unless the signal is too weak). The VGA gain should be almost always set to zero as it doesn’t contribute to the SNR at all while keeping the dongle warmer and so more thermal noise.

In the R820T2 i2c register specs there are some other interesting features, currently unexposed. One of them is the band selection filter (lo/med/high) which apparently is even used in the librtlsdr driver. I found changing that has absolutely no effect for me unfortunately. It might have provided opportunities for better reception around the “verge” where the librtlsdr driver switches them (approx. at 310MHz and 588MHz). But switching them has absolutely no effect.

The new fully adjustable driver by gat3way.
The new fully adjustable driver by gat3way running in GQRX.