Category: Amateur Radio

Monitoring FT8, JT65, JT9 on Multiple Bands with Low Cost Single Board PCs

Thank you to Michael (dg0opk) who wrote in and wanted to share details of his full SDR monitoring system for weak signal HF modes. His setup consists of nine ARM mini PCs (such as Banana Pi's, Raspberry Pi's, and Odroid's), several SDRs including multiple RTL-SDR's, an Airspy Mini, FunCube Dongle and SDR-IQ, as well as some filters and a wideband amp. For software he uses Linrad or GQRX as the receiver, and WSJTx or JTDX as the decoding software, all running on Linux.

Michael also notes that his Bananapi FT8, JT65 and JT9 SDR monitor has been up and stably running continuously for half a year now. Bananapi's are lower cost alternatives to the well known Raspberry Pi single board computers, so it's good to note that a permanent weak signal monitoring system can be set up on a very low budget. Presumably even cheaper Orange Pi's would also work well.

With his setup he is able to continuously monitor FT8, JT65 and JT9 on multiple bands simultaneously without needing to tie up more expensive ham radios. His results can be seen on PSKReporter. A video of his RTL-SDR Raspberry Pi 3 decoding FT8, JT65 and JT9 can be found here.

Weak Signal Receiver Setup
dg0opk's weak signal receiver setup

Creating a High Altitude Balloon Telemetry System with Raspberry Pi, RPiTX and RTL-SDR

The 2M TX Filter by ZR6AIC
The 2M TX Filter by ZR6AIC

Over on his blog ZR6AIC explains how he's created a full HAB (high altitude balloon) telemetry transmit and receive system using RPiTX and an RTL-SDR dongle running on a Raspberry Pi 3.

RPiTX is software that enables the Raspberry Pi to transmit any modulated signal over a wide range of frequencies using just a single GPIO pin. However, the transmission contains multiple harmonics and thus requires sufficient filtering in order to transmit legally within the 2M ham band. To solve this ZR6AIC uses a 2M Raspberry Pi Hat kit which he designed and created that contains two low pass filters as well at the option for an additional power amplifier.

The rest of ZR5AIC's post explains how his HAB telemetry system combines the Raspberry Pi 3, RPiTX 2M Hat, RTL-SDR, a GPS unit, battery, temperature sensor and optional camera into a full HAB transmitting system. He also explains the software and terminal commands that he uses which allows him to transmit via RPiTX a CW beacon and GPS and temperature sensor APRS telemetry data with the Direwolf software. Full instructions on setting up the alsa-loopback audio routing is also provided.

Launching the High Altitude Balloon.
Launching the High Altitude Balloon.

Thomas N1SPY Demonstrates Receiving SSTV Images from the ISS

Earlier in the month the International Space Station (ISS) was transmitting SSTV images down to the earth for anyone to receive an decode. The ISS does this several times a year to commemorate special space related events, such as the day Yuri Gagarin (first man in space) was launched.

In the video Thomas explains why the ISS does this, how to track the ISS, and then he demonstrates actually receiving and decoding the signal. Thomas uses an Airspy HF+ to receive the signal on 145.8 MHz, however an RTL-SDR could do the same job. For decoding he uses the MMSSTV software.

For new on when the ISS might transmit SSTV again, keep at eye on the ARISS Blog, and the ISS Ham Twitter page.

2018: Thomas N1SPY receives SSTV signals from the ISS

OH2BNF’s Plan for a Large Scale Raspberry SDR (LSR-SDR) Based on RTL-SDR Dongles

Thanks to OH2BNF for writing in and sharing his plan to build a "Large Scale Raspberry SDR" (LSR-SDR), which will be based on RTL-SDR dongles. To create the LSR-SDR he plans to take a 19" rack which can support up to 40 Raspberry Pi 3's, plus up to 160 USB devices, and turn it into a massive SDR array. The rack is key as it allows for simple power management of all the Pi's and other devices to be connected.

OH2BNF plans to connect 20 or so RTL-SDRs, with some operating individually and with others operating coherently via a common external oscillator. The rack may also contain some transceivers, an ICOM IC-7300, antenna switches, upconverters, LNAs and other hardware too. Once completed he hopes to move the system to a low RFI environment and operate the unit entirely remotely. With this he hopes to solve his local RFI issues. He also writes regarding applications:

Primary objectives are to incorporate automated adaptivity to the system at large – for example leveraging on band condition information, WSPR (Weak Signal Propagation Report) & friends, automated signal detection and decoding, great flexibility in terms of individual cluster nodes being able to fast respond to various needs and tasks, strong emphasis in parallel processing where applicable depending on the problem type and dataset, support for multiple end users benefiting from the computing and reception capacity of the cluster – to name the most significant.

It's an interesting idea for sure, and we hope to see some updates from OH2BNF in the future.

The Raspberry Pi 19" Rack
The Raspberry Pi 19" Rack

Using a HackRF to Transmit To a Local Repeater

Over on YouTube Tech Minds has uploaded a new video where he shows how he can use his HackRF SDR with the SDRAngel software to easily transmit voice to a local ham radio repeater. If you are unfamiliar with ham radio, a ham repeater is simply a radio station that receives voice or other signals on a certain ham radio frequency, and re-transmits the signal with stronger power on another frequency. This allows communications to be receivable over a much larger distance.

SDRAngel is a very nice piece of SDR software that has controls for TX capable SDR's like the HackRF. In the video Tech Minds shows the HackRF being used as a transmitter, with it transmitting to a repeater at 145.137 MHz. An RTL-SDR is then used to listen to the repeater output at 145.737 MHz. With this set up he is able to contact a friend via the repeater easily.

It doesn't appear that Tech Minds is using any sort of external amplifier, so this shows that the HackRF is powerful enough to hit local repeaters just by itself.

Transmitting With A HackRF One Via My Local Ham Radio Repeater

Demonstrating the MFJ-1708SDR Automatic Relay Switch with an SDRplay and Icom IC7300

A few weeks ago we posted about the MFJ1708SDR automatic relay switch and how it can be used to combine an RX only SDR with a transmit capable radio. An automatic antenna relay switch is used to automatically ground the SDR's antenna input whenever the TX capable radio transmits in order to protect the SDR's front end from blowing up due to high TX power.

In this YouTube video Pete Sobye shows us the MFJ1708SDR working together with an Icom IC7300 HF radio and an SDRplay which is being used as a panadapter. For software Pete uses HDSDR and Omnirig which allows the PC to control the IC7300.

Icom IC7300 panadapter MFJ-1708SDR, SDRPlay, HDSDR and OmniRig

Using a Transmit/Receive Switch to Protect an SDR from a Transmit Radio

A question that comes up often is how to combine an RTL-SDR, or any other RX only SDR with a transmit capable amateur radio. It's not possible to connect the RX only SDR together with the TX radio via a standard splitter because the TX radio's power will most likely blow up the SDR with it's powerful output. To solve this problem you need either a manual switch that will switch out the SDR when transmitting which requires absolute discipline to not accidentally transmit in the wrong switch position, or an automatic relay switch.

Over on YouTube channel HamRadioConcepts has given a good overview and demonstration of the MFJ-1708SDR Transmit/Receive automatic relay switch, which is a good product that solves this issue. It is also a fairly budget friendly option, coming in at only US$79.95 over on the MFJ website. HamRadioConcepts notes that the switch automatically grounds out the SDR whenever the PTT on the radio is pressed, and also has a fail safe that will automatically detect a transmission and ground the SDR if PTT is disconnected.

MFJ-1708SDR Transmit/Receive Switch For SDR Receivers

GridTracker Now Available on Windows, Mac and Ubuntu (Debian)

In early February we posted news about the release of a program called GridTracker. GridTracker is a live mapping program for WSJT-X which is a software decoder for low power weak signal ham communications modes such as FT8, JT4, JT9, JT65, QRA64, ISCAT, MSK144 and WSPR. Although these are low power modes, the protocols are designed such that even weak signals can potentially be received from across the world. Mapping the received signals can be interesting as it may give you an idea of current HF propagation conditions.

Previously GridTracker was Windows only software. However recently GridTracker was updated to now include support for Mac and Ubuntu (Debian) operating systems as well. This is great news as it makes it much easier to set up a portable GridTracker screen on a portable computer like a Raspberry Pi.

GridTracker Mapping out Weak Signal Communications.
GridTracker Mapping out Weak Signal Communications.