January 13, 2015

TCP Enabled version of librtlsdr

Recently RTL-SDR.com reader Fabien wrote in to let us know that he has created a new version of the librtlsdr RTL-SDR drivers which have built in TCP support.

Fabien built a remote SDR using a BeagleBone Black mini embedded computer and put it outside for better reception and to be closer to the antenna. When trying to remotely access the dongle he discovered some problems. He writes:

I then access the dongle over TCP from an indoor PC. One issue is that some existing tools such as rtl_fm, rtlizer or rtlsdr_waterfall lacks TCP/IP connectivity.

To solve this problem, I added TCP support to the rtlsdr library. When a tool communicates with the now physically distant dongle, this new implementation transparently forwards the data using TCP instead of USB. It allows one to use existing tools without modifying them. Also, it allows a developer to use the same librtlsdr, no matter whether the dongle is local or distant.

The implementation is located here: https://github.com/texane/librtlsdr
branch: rpc

To use it, one must compile and install the library. Then, a server (called rtl_rpcd) must be run on the remote location (in my case, the beagle bone black at address 192.168.0.43): RTLSDR_RPC_SERV_ADDR=192.168.0.43 \ rtl_rpcd

Then, the existing tool (for instance rtlizer) can be run using:
RTLSDR_RPC_IS_ENABLED=1 RTLSDR_RPC_SERV_ADDR=192.168.0.43 \
rtlizer

Outdoor RTL-SDR Receiver Running on a BeagleBone Black

Tweet13

Vote

13 Shares

January 13, 2015

Comparison of several SDRs on degradation from nearby strong signals at broadcast FM frequencies

The programmer of Linrad (aka Leif sm5bsz) has uploaded a video to YouTube that compares several software defined radios on dynamic range and compression performance in the presence of strong nearby signals. In the video Leif tests the Airspy, BladeRF with B200, FDM-S1, Funcube Pro+, rtlsdr/E4000, rtlsdr/FC0013, rtlsdr/R820T, SDR-14 and SDRplay.

The main test works by tuning to a broadcast band FM frequency and then injecting a strong carrier signal at distances of 500 kHz, 1 MHz, 2 MHz and 5 MHz from the center frequency. The carrier signal strength is slowly increased until the SDR shows signs of complete degradation of reception of the FM signal. Better SDRs will tolerate stronger nearby signals without degradation.

The results are summarized at 34:20, 1:21:38 and 1:48:30. We have also taken screencaps of the results at 1:21:38 and 1:48:30 and they are shown below. The first column is when a higher gain is used, and the second column is when a lower but still barely copyable gain level is used. In the Levels for loss of performance columns smaller numbers are better and in the Dynamic range columns larger numbers are better. Finally, at the end of the video starting at 1:45:55 Leif also tests the spur performance of the SDRs.

results_3 — Results at 2 MHz and 5 MHz Seperation

SDR on 88-108 FM part1

Watch this video on YouTube

Vote

January 12, 2015

New Oregon Scientific Temperature/Humidity Data Receiver Software for MacOS and RTL-SDR

Recently programmer Erik Larsen wrote in to us to let us know about a MacOS application he has been developing to receive temperature and humidity data from Oregon Scientific v2.1 sensors. Oregon Scientific manufactures popular electronic weather stations that transmit data from remote sensors wirelessly. Using an RTL-SDR and Eriks software it is possible to receive the weather station data on a Mac computer and display the data on a GUI. The software can be downloaded from the releases section on its GitHub page.

Note that there are also several Linux based Oregon Scientific decoders available including rtl-433m-sensor, rtl_osv21, and rtl-wx.

Vote

January 12, 2015

Receiving VOR Radio Navigation with an RTL-SDR and GNU Radio

Over on YouTube user hpux735 has uploaded a video where he explores the feasibility of receiving VOR radio navigation signals using GNU Radio and an RTL-SDR. VOR is an acronym for VHF Omni Directional Radio Range and is an older method of navigation used by aircraft which is quickly being made redundant due to GPS navigation. VOR uses two signals, one master omnidirectional signal and one rotating directional signal. By doing some calculations on the received phase of these two signals it is possible to determine the angle of the aircraft from the transmitter.

In the video hpux735 explains and discusses the VOR signal and also shows how to use these signals for navigation with an RTL-SDR and GNU Radio flowchart. To receive the VOR signal he uses an RTL-SDR to record the VOR signal while he drives around with a car. Then later he uses his GNU Radio program to generate a plot that shows when he is moving and in which direction.

hpux735 has also uploaded some supplemental material over on his blog. In the future he hopes to correlate his VOR results with GPS coordinates that he will take whilst actually flying around.

VORs and SDRs part 1: Playing with angles

Watch this video on YouTube

Tweet16

Vote

16 Shares

January 12, 2015

Analyzing Radar Pulses with Baudline and an RTL-SDR

Over on YouTube user Albert Schäferle has uploaded a short video showing his reception of some radar pulses and their corresponding echoes. He uses rtl_fm and pipes the output into Baudline which is used to display the radar waveform. On the video description he writes:

Receiving direct and (supposedly) reflected pulses from an L-band radar in Učka, HR (Lockheed Martin AN/FPS-117). The receiving station was 83 km away, with clear LOS.
Center frequency is 1258 MHz (one out of four that this frequency-agile radar head is using).
The receiver is a RTL-SDR dongle (R820T tuner IC) with a 2-dipole collinear array (tuned for 403 MHz) and approx 7 m of Belden 1694A RG-6 coax.

rtl_fm output was piped to baudline, which is the software shown in the video. The IQ sampling rate is 2 MHz; the transform is a complex STFT (size=2048 samples, Blackman window).
This is a 0.008x speed playback of 15 ms of recording.
The (again, supposedly) reflected pulses are obviously more time-local with a shorter transform window size, e.g. 512 samples http://i.imgur.com/sAHWhwD.png

The effect of pulse compression is quite evident http://www.radartutorial.eu/08.transm…
The direct-reflected delay is approx 278 µs (~42 km from receiver, in a simple 2D, along beam, normal incidence model). I should add that this “reflection delay” effect does not usually show up.
There’s another fainter echo closer to the pulse, but I suspect that it could be a time-sidelobe of the main pulse: a side effect of pulse compression. Anyway, I must state that I have no formal knowledge on radar topics. So you’d better take all this with a grain of salt 😉

Link to recording: https://db.tt/Lxe67Ig3 (save destination as…)

Video recorded with VLC, audio piped to stdout and saved, then synced in Blender.

Radar WGS84 coordinates: 45.286757,14.202732 http://www.panoramio.com/photo/26952908

Analyzing radar pulses with Baudline and RTL-SDR.

Watch this video on YouTube

Tweet30

Vote

30 Shares

January 9, 2015

Compiling and using DSD 1.7 for D-STAR on Linux

Amateur Radio hobbyist George Smart has recently written a tutorial showing how to compile and install DSD v1.7 on a Linux computer in order to receive D-STAR digital voice. D-STAR is a digital voice protocol used by hams at a frequency of 145.670 MHz.

The tutorial shows the entire set up process from installing the required dependencies to running DSD 1.7 with GQRX by piping audio through UDP into DSD. He also shows how to run DSD 1.7 on a Raspberry Pi.

Note that DSD v1.7 also runs on Windows, and this previous post links to a precompiled Windows binary file.

Vote

January 9, 2015

Beaglebone Black FM/Internet Radio Combo Receiver using an RTL-SDR

Last year we missed this interesting project by Frederick Vandenbosch where he created a FM/internet radio combination receiver using a BeagleBone Black mini embedded PC and an RTL-SDR dongle.

The idea is that the system will receive FM radio through the RTL-SDR normally, but when reception is poor or unavailable you can switch to internet radio which is received through WiFi. The radio is controlled through an LCD screen attached to the BeagleBone Black.

Frederick used Linux on the BeagleBone and created a custom GUI that allows for easy tuning using rtl_fm as the RTL-SDR back end, setting channel presets and for switching between internet and live FM radio.

BeagleBone Blade FM/Internet Radio Combo Receiver

Beaglebone Black Digital Radio with RTL-SDR and Wifi

Watch this video on YouTube

Vote

January 8, 2015

Receiving VLF with a PC sound card, Miniwhip Antenna and SAQrx

Over on YouTube user Mile Kokotov has uploaded a video showing how he is able to receive Very Low Frequency (VLF) signals between 300 Hz to 30 kHz using just his PC, a Miniwhip antenna connected to his sound card input port and a program called SAQrx Panoramic VLF Receiver. This allows reception of signals between 0-48 kHz with a sound card that can sample at 96 kHz.

Using this set up he is able to receive the Alpha navigation system beacons which are at around 10-12 kHz and some other Navy navigation system beacons between 18 and 48 kHz from his home in Macedonia.

Receiving VLF with PC and software only

Watch this video on YouTube

Vote